MICROMILL Sawmills

MICROMILL SAWMILLS

 micromill  

Micromill Systems Inc. is a Canadian controlled, private corporation operating in Summerland, British Columbia.


 

The Micromill is designed specifically for small-log processing and directly addresses the developing niche market brought on by economic and environmental pressures for better forest management.

                         --------------

The Micromill SLP5000D & SLP5000E small log processors are designed specifically for moderate size sawmill operations requiring a low cost solution for processing treetops, salvage wood & small logs. The unique modular design and construction.

                         --------------

Low investment cost with a return of investment typically of less than 24 months. Highly automated, modularized system minimizes set-up time and size of the operating crew.  The mill requires a crew of only 3 or 4 people. The entire mill layout is very compact and can be set up on a 14m x 25m site.

                         --------------

   

 


We offer the following models:

MICROMILL MODEL SLP5000D - Avg. Processing Speed:22m/min.; Max./Min. log diameter: 325/100 mm; Max./Min. log length:6/1 m; 300/350-hp diesel engine.

MICROMILL MODEL SLP5000E - Avg. Processing Speed: Max./Min. log diameter: 325/100 mm; Max./Min. log length:6/1 m; 344-hp electic motor power.

 

MODEL SLP5000D                                                                                                                       

Micromill_1.jpgMicromill_2.jpgMicromill_4.jpgMicromill_5.jpgMicromill_6.jpgMicromill_8.jpgMicromill_9.jpgMicromill_10.jpg

________________________________________

 

BASE UNIT:
• Micromill 5000 Series Sawbox.
• Diesel frame installed in 6m container.
• Four Micromill sealed Chipping Head Spindle Bearing units.
• Four Micromill chipping heads c/w standard ring saw attachment.
• Two sealed Micromill Arbor Saw units.
• Series 25-blower system for chip removal.
• Von Ruden 1:1 ratio spiral gear box.
• Pneumatic pressure auto centering In-feed system.
• Four-roll Out–feed.
• One set each Chipping Knives, Ring Saws and Groove Saw/Dados.
POWER:
• 300hp Caterpillar C9 electronic industrial diesel engine.
• Rockford single disk PTO.
• Standard cooling system; 125 degree ambient temperature.
• 13.2 CFM air compressor c/w 60 gallon reserve tank.
• 24-volt alternator & starter.

 

Technical data: pdficon large

   

    

MODEL SLP5000E                                                                                                                       

....  

________________________________________

 

 

BASE UNIT:
• Micromill 5000 Series Sawbox.
• Electric base frame installed in 6m container.
• Four Micromill sealed chipping head drive units.
• Four Micromill chipping heads c/w standard ring saw attachment.
• Double arbor saw unit c/w two sealed Micromill arbor drive units
• Series 50 external-blower system for chip removal
• Pneumatic pressure auto centering in-feed system.
• Four roll out–feed.
• One set each Chipping Knives, Ring Saws, Goove Saw and Dados
POWER:
• 1 – 100hp electric motor (side heads/groove saw).
• 1 – 75hp electric motor (vertical mount, top & bottom heads).
• 1 – 75hp electric motor (arbor saws).
• 1 – 50hp electric motor (blower system)
• 1 – 40hp electric motor (hydraulic system).
• 1 – 4hp electric motor (green chain).
• 1 – 6 section MCC panel c/w soft starts on all motors over 40hp.
• Lock outs for all motors.


 

Technical data: pdficon large

   

    

 

 

Know How EN

.